T2SSK2DQ
16-Door Altronix/Lenel-S2 (S2 Security Platform) Access and Power Integration Kit - Trove2SS2 with eFlow104NB, eFlow102NB, (2) LINQ8ACMCB, (2) LINQ8PDCB, NetWay5B, RSB1,RSB2
Altronix T2SSK2DQ kit consists of Trove2 enclosure, TSS2 Lenel-S2 (S2 Security Platform)/ Altronix backplane with one (1) 24VDC @ 10A power supply/charger, one (1) 12VDC @ 10A power supply/charger, two eight PTC protected dual input/output network/managed access control modules and two eight PTC protected dual input/output network/managed power distribution modules. Also included is a 5-Port hardened switch board. This kit also accommodates S2-INST Installation Kit For Lenel-S2 (S2 Security Platform) S2 Network Node for up to sixteen (16) doors in a single enclosure. Trove simplifies board layout and wire management, reduces installation time and labor costs.
Specifications
eFlow104NB Power Supply/Charger - 1
Input
- Voltage: 120VAC, 60Hz, 4.5A max.
- Input Fuse: 6.3A / 250V.
Output
- Voltage: 24VDC @ 10A.
- Auxiliary: 1A (unswitched).
- Protection: Overvoltage protection. Filtered and regulated.
eFlow102NB Power Supply/Charger - 2
Input
- Voltage: 120VAC, 60Hz, 3.5A max.
- Input Fuse: 5A / 250V.
Output
- Voltage: 12VDC @ 10A.
- Auxiliary: 1A (unswitched).
- Protection: Overvoltage protection. Filtered and regulated.
Both Power Supplies
Battery Charging
- Capacity: 12VDC/12AH (2 within enclosure); 40AH/65AH (requires separate enclosure)
- Type: Sealed lead acid or gel type
- Failover: Upon AC loss, instantaneous
- (Batteries are sold separately).
Fire Alarm Disconnect
- Supervised: Latching or non-latching.
- EOL 10K Resistor.
Supervision
- AC Failure: Form “C” contacts.
- Battery: Form “C” contacts.
- Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 71-73% for 12V units and 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
Indicators LED
- AC Input: 120VAC is present.
- DC Output: Powered.
- Battery: Discharged or not connected.
Two (2) LINQ8PDCB Network Power Distribution Modules
Input
- Voltage: 24VDC from eFlow104NB and 12VDC from eFlow102NB
- Input PTCs 9A.
Outputs
- PTC protected auto-resettable outputs.
- Any of the eight (8) PTC protected power outputs are selectable to follow power Input 1 or Input 2
- Individual outputs may be set to OFF position for servicing
Output PTCs:
- 2.5A
Status Monitoring
- Power Supply output voltage and load, Voltage and load of each output
- FACP trigger and reset status, Unit temperature (Celsius)
- Power Supply AC and Battery status, Battery health
Reporting:
- Windows Dashboard Alert messages
- E-mail notifications, Event Log tracks history
Indicators (LED)
- Bat Local: Charging current status
- FACP: Triggered / Released
- Input: Input signal
- Out1 - Out8: Output status
Two (2) LINQ8ACMCB Networked Access Power Controllers
Input
- Voltage 24VDC from eFlow104NB and 12VDC from eFlow102NB
- Input PTC: 9A
Outputs
- PTC protected auto-resettable outputs
- Any of the eight (8) PTC protected power outputs are selectable to follow power Input 1 or Input 2
- Individual outputs may be set to OFF position for servicing
Output PTCs:
- 2.5A
Programming Features:
Eight (8) Programmable Outputs:
- - Fail-safe, fail-secure or auxiliary outputs
- - Input controlled or manually controlled through software
- - High (over) and low (under) voltage and current monitoring by output
- - Multiple outputs may be programmed to be triggered by a single input
- - Battery back-up by output
Eight (8) Programmable Trigger Inputs:
- - Normally open (NO), Normally closed (NC) or Open collector sink inputs
- - Wet Input (5VDC - 24VDC) with 10k resistor
- - Any combination of the above
Other Programmable Trigger Inputs:
- - Monitor power supply(ies) input for voltage and current limits (high/low)
- - Input and output current calibration, Programmable timer events
- - Programmable user levels, Enable or disable alerts by type
- - Programmable alert reporting delay
Indicators (LED)
- Green AC LED: indicates AC trouble condition
- Green BAT LED: indicates battery trouble condition
- Green FACP LED: indicates FACP disconnect is triggered
- Flashing Blue Heartbeat LED: indicates network connection
- Individual OUT1 - OUT8 Red LEDs: indicate outputs are triggered
- Individual Voltage LEDs: indicate 12VDC (Green) or 24VDC (Red)
NetWay5B 5-Port Hardened Switch
Input
- 24VDC, current draw: 150mA
Ethernet Ports:
- Five (5) 10/100/1000 Mbps ports.
- Connectivity: RJ45, auto-crossover.
- Wire type: 4-pair CAT5 or better structured cable.
- Distance: up to 100m.
- Speed: 10/100/1000 Mbps, half/full duplex, auto negotiation.
Indicators (LED)
- Individual PoE On LEDs for each port.
- Individual IP Link status, 10/100Base-T/active LEDs for each port.
Environmental
Temperature
- Operating: 0° C to 49° C (32° F to 120° F).
- Storage: - 20° C to 70° C ( - 4° F to 158° F).
Relative Humidity
- Relative Humidity: 85% +/- 5%.
BTU/Hr. (approx.):
- 196 BTU/Hr.
Agency Listings
CE Compliant
Accessories
| Name | Description |
|---|---|
| WM25 | Magnetic Cable Tie Mounts |
| WM5 | Magnetic Cable Tie Mounts |
| WM100 | Magnetic Cable Tie Mounts |
| MM4 | Mounting Magnets, Four (4) Quantity per Pack |
| MM8 | Mounting Magnets, Eight (8) Quantity per Pack |
| MM12 | Mounting Magnets, Twelve (12) Quantity per Pack |
| MM24 | Mounting Magnets, Twenty Four (24) Quantity per Pack |
| BR1 | Add-On Mounting Bracket |
| Trove2BWC | Battery/Wire Trough Enclosure |
Dimensions & Weight
Enclosure:
- Wall mount enclosure for indoor use.
- Accommodates up to four (4) 12VDC/12AH Batteries.
- Dimensions 21.5"W x 27.25"H x 6.5"D (546.1 mm W x 692.15 mm H x 165.1 mm D).
- 3/4" and 1" combination knockouts.
Weights (approximate):
- Product Weigtht: 58.3 Lbs. (26.4 kg).
- Shipping Weigtht: 63.3 Lbs. (28.7 kg).