T3MKR77P8V

8-Door Altronix/Mercury Access and Power Integration Wired Kit - Trove3M3 with (2) eFlow104NBV, PDS8, CIRC1ATS, BR1, wire harnesses and finger duct

Altronix T3MKR77P8V is a 16-door access and power integration kit which includes Altronix power and sub-assemblies along with factory installed wire management for Mercury hardware. This unit provides ample power to support Mercury platform controllers and locking devices. The T3MKR77P8V accommodates up to one (1) Intelligent Controller and seven (7) Dual Reader Interface Modules. Trove Plus simplifies field installations and provides reliable, robust critical power and control for the most demanding applications.
*Also compatible with these authentic Mercury partners:
AccessNsite, Avigilon, BadgePass, BluBox, Feenics, Genetec, Identicard, IMRON, Johnson Controls, Kastle, Keri Systems, LockState, Maxxess, Midpoint Security, NLSS, Open Options, Panasonic i-PRO MonitorCast, Quintron, RS2, S2 Security, Schneider Electric, Vanderbilt.

  • Two (2) eFlow104NBV Power Supply/Chargers
      • Input
        • Voltage: 220VAC (working range 198VAC - 256VAC), 50/60Hz, 5.4A
        • Main Fuse: 6.5A / 250V.
      • Outputs
        • Voltage: 24VDC @ 10A.
        • Auxiliary: 1A (unswitched).
        • Other: Overvoltage protection. Filtered and regulated.
  • Battery Charging
    • Capacity: 12VDC/12AH (4 within enclosure), 40AH/65AH (requires separate enclosure)
    • Type: Sealed lead acid or gel type.
    • Failover: Upon AC loss, instantaneous.
    • (Batteries are sold separately).
  • Fire Alarm Disconnect
    • Supervised: Latching or non-latching.
    • EOL: 10K Resistor.
  • Supervision
    • AC Failure: Form “C” contacts.
    • Battery: Form “C” contacts.
    • Low DC Power Shutdown: Shuts down DC output terminals if battery voltage drops below 70-75% for 24V units (depending on the power supply). Prevents deep battery discharge.
  • Indicators LED
    • Input: 220VAC is present
    • DC Output: 24VDC is present
    • Battery: Discharged or not connected
  • Circ1ATS - AC Power Transfer Switch
      • Input
        • Two (2) Independent AC Inputs: 120 or 240VAC up to 10A each
      • Output
        • One (1) AC output: 120 or 240VAC up to 10A
      • Features
        • Removeable AC Terminal Blocks
        • Brownout Threshold Adjustment
        • Restore Delay Adjustment
        • DIN Rail mountable (DNP1)
      • Supervision
        • AC Failure (Primary and Secondary Inputs) Form “A” Normally Closed contacts
      • Indicators LED
        • LED Indicators of Primary and Secondary Power
  • PDS8 Dual Input Power Distribution Module
      • Input
        • Voltage: 24VDC from eFlow104NBV
        • Input Fuses: 10A/32V.
      • Outputs
        • Voltage: 24VDC.
        • Any of the eight (8) power outputs are selectable to follow power Input 1 or Input 2
        • Individual outputs may be set to OFF position for servicing.
      • Outputs Ratings
        • Fuses are rated 3A/32V.
      • Indicators (LED)
        • DC Output: Eight (8) individual output LEDs.
        • Green: 12VDC (if used)
        • Red: 24VDC.
  • Environmental
      • Temperature
        • Operating: 0° C to 49° C (32° F to 120° F).
        • Storage: - 20° C to 70° C ( - 4° F to 158° F).
      • Relative Humidity
        • Relative Humidity: 85% +/- 5%.
      • BTU/Hr. (approx.):
        • 289 BTU/Hr.
 
CE Compliant
 
Components of this Trove kit are UL Listed sub-assemblies. Please refer to the corresponding Sub-Assembly Installation Guides for further information. Sub-assembly components of this kit can be found under the "Kit Contents" tab.
 
TAA Compliant
 
NDAA Compliant
 
BAA Compliant
Name Qty Description Agency Listings
Trove3 1 Access and Power Integration Enclosure, Requires compatible Trove3 Series Backplane
TM3 1 Trove3 Backplane for Altronix & Mercury
eFlow104NBV 2 Power Supply Charger, Single Output, 24VDC @ 10A, Aux Output, FAI, LinQ2 Ready, 220VAC, Board
PDS8 1 Dual Input Power Distribution Module, 8 Fused Outputs
Circ1ATS 1 High Voltage AC Automatic Transfer Switch. Board
BR1 1 Add-On Mounting Bracket
Enclosure:
  • Wall mount enclosure for indoor use.
  • Accommodates up to four (4) 12VDC/12AH Batteries.
  • Dimensions 30.12"W x 36.12"H x 7.06"D (768.1 mm W x 917.5 mm H x 179.3 mm D).
  • 3/4" and 1" combination knockouts.
Weights (approximate):
  • Product Weight: 85.6 Lbs. (38.83 kg).
  • Shipping Weight: 98.8 Lbs. (44.82 kg).
Configure Trove Print

Access controllers not included

*Batteries sold separately
Documentation
Lifetime Warranty Locate a Distributor